RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: old p47
Showing results 1 to 16 of 16
Search took 0.02 seconds.
07-28-2015, 12:50 PM
Replies: 1,681
Views: 454,925
Posted By old p47

right on top of the motor box under the muffler....

right on top of the motor box under the muffler. I used a DLE 61. Get the aeroworks muffler to clear the side of the cowl. Or you will need someone to trim the muffler at the exhaust port and weld it...
06-10-2015, 04:18 PM
Replies: 1,681
Views: 454,925
Posted By old p47

Yellow that will work if you take the template...

Yellow that will work if you take the template they have in the kit for a duct and re-make it from some .o625 G-10 and set the duct right above the front inlet upper lip. I glued a small block to the...
06-08-2015, 05:03 PM
Replies: 1,681
Views: 454,925
Posted By old p47

yes it is completely inside. It is a DLE

yes it is completely inside. It is a DLE
06-08-2015, 02:27 PM
Replies: 1,681
Views: 454,925
Posted By old p47

If you go back in this thread a Horizon pilot...

If you go back in this thread a Horizon pilot pointed out you need to put a spoiler in front of you air exit hole to create a low pressure area to draw out the hot air. I fly in phx and have 9...
05-26-2015, 06:29 AM
Replies: 1,681
Views: 454,925
Posted By old p47

SJ I think you did the right thing ordering the...

SJ I think you did the right thing ordering the air retract option. Like I said the struts and blocks are very strong. As you stated the motors are very small. I was looking at a friends set of...
05-25-2015, 09:51 AM
Replies: 1,681
Views: 454,925
Posted By old p47

I do not know. The struts the block and mounts...

I do not know. The struts the block and mounts are very sturdy I do not think you would gain much buying siera other than it being air. Horizon needs to get on it and do some QC.
05-25-2015, 08:45 AM
Replies: 1,681
Views: 454,925
Posted By old p47

I need some help I got 4 more fights in going...

I need some help I got 4 more fights in going inverted after take off to get the right side gear to go up. On the 8th landing the right gear partially collapsed, it looked like a folk wolf. Once on...
05-18-2015, 02:12 PM
Replies: 1,681
Views: 454,925
Posted By old p47

CuckK2 you seem to have some info on the electric...

CuckK2 you seem to have some info on the electric retracts. I have the over current on 10 and the only way I can get the right side door closed is to take off go inverted on a 45 up line and hit the...
04-29-2015, 01:52 PM
Replies: 1,681
Views: 454,925
Posted By old p47

I also have never hit a cactus but I have had ...

I also have never hit a cactus but I have had flame oust and even with a careful decent, that on a grass or smooth dirt field would be just a clean up of the bottom of the fuse, ends up with jagged...
04-29-2015, 12:29 PM
Replies: 1,681
Views: 454,925
Posted By old p47

At our field its better to have gear up if you do...

At our field its better to have gear up if you do not make the runway lots of bushes rocks and cactus
Mike
04-29-2015, 10:29 AM
Replies: 1,681
Views: 454,925
Posted By old p47

Ok SJ so as soon as the wheels leave the ground...

Ok SJ so as soon as the wheels leave the ground hit the retract switch? I am going out tomorrow and I put a separate 2200 mha LiFe battery on the power impute to the controler. I hoping for a flight...
04-27-2015, 10:29 AM
Replies: 1,681
Views: 454,925
Posted By old p47

All done have two flights. Here are some facts....

All done have two flights. Here are some facts. The programing instructions of the retract door control is not on one document. You need to get the door channels going into the controler from the...
04-07-2015, 06:48 PM
Replies: 1,681
Views: 454,925
Posted By old p47

Ok I give it a try

Ok I give it a try
04-07-2015, 12:57 PM
Replies: 1,681
Views: 454,925
Posted By old p47

Thanks I have the vertical offsett as well but my...

Thanks I have the vertical offsett as well but my main concern is the gap at the LE and it is tight at the TE. IF I sand the rib on the center section and the tube is out it might not fix it.
04-07-2015, 09:24 AM
Replies: 1,681
Views: 454,925
Posted By old p47

Has anyone else had wing to center section...

Has anyone else had wing to center section mis-aligment? On the right side the TE is up tight and the LE is out about 3/16th. Not sure if it is the tubes or the ribs. Any ideas on fixing this.
04-04-2015, 08:54 PM
Replies: 1,681
Views: 454,925
Posted By old p47

Gib you have to use a programmable retract servo...

Gib you have to use a programmable retract servo that is why they list the spektrum 7040 or the older 7000 works just lower voltage
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.