RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Tennwalker41-delete
Showing results 1 to 9 of 9
Search took 0.11 seconds.
Forum: Glow Engines
02-25-2007, 07:47 AM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

NOt real bad i would say around 1 1/2 oz a minute if u run it fulll open. ITs a power house.
Forum: Glow Engines
02-24-2007, 11:58 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

Its all i can do to hold on to it with one hand when u stab the throttle and i am fairly strong ( 21 years in USMC). I could hardly believe it myself when i got it. I Love the engine i just want to...
Forum: Glow Engines
02-24-2007, 11:40 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

I am bein completely honest when i say that a Saito 220 although only rated at 3.5hp will pull u a 50cc gas engine backwards. I have a Fpe 3.4 to compare it against.
Forum: Glow Engines
02-24-2007, 11:35 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

An 18x6 is a small prop for the 220 according to Saito they can run up to a 22x8 or do u mean in general???
Forum: Glow Engines
02-24-2007, 11:27 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

I was down to about 2 1/4 and still getttin about 8500 with a APC 18x6 is that too lean?? WOuld that cause problems setting the low needle?? thanks for alll the help
Forum: Glow Engines
02-24-2007, 11:11 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

Where is ur 150 high speed needle finnaly set??
Forum: Glow Engines
02-24-2007, 10:53 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

It will run fine for about 30 seconds then just sputter and quit. DO i need to go back and forth on the needles?? Mine low needle even though it says 1 1/2 turns in from flush has to go almost...
Forum: Glow Engines
02-24-2007, 10:32 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

U can say that again .. I have been doin that the whole week. I love the way it runs like a sewing machine but this engine is a lot of trouble so far. ON the 220 and 180 it says that the factory...
Forum: Glow Engines
02-24-2007, 09:58 PM
Replies: 54,867
Views: 5,419,839
Posted By Tennwalker41-delete

RE: Welcome to Club SAITO !

Can someone please help.!! I have a new 220 and i cannot get it to idle more than 30 seconds without quittin. I cant believe this engine is that sensitive. I dont really know much about a Saito some...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.