RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: johnboy151a
Showing results 1 to 18 of 18
Search took 0.08 seconds.
Forum: Glow Engines
02-15-2020, 06:48 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Thanks for the input on converting to Gas. The...

Thanks for the input on converting to Gas. The meat of my question is about how are the engines holding up mechanically. I realize that some power is lost compared to Glow fuel. But are the big...
Forum: Glow Engines
02-14-2020, 02:19 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

A question for the group. I'm sure that this has...

A question for the group. I'm sure that this has been discussed at length here, but the Net is very slow out here where I live and RCU takes a good deal of time to load and search.
So. How are the...
Forum: Glow Engines
06-01-2014, 02:49 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Yes sir I did. I hate to tell you this, but I...

Yes sir I did. I hate to tell you this, but I could not figure it out so I sent it back to C&H and he re-tuned it. I never could get a straight answer out of him regarding what needed to be redone....
Forum: Glow Engines
05-31-2014, 06:37 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

I have two 1.50's that I want to convert to CDI. ...

I have two 1.50's that I want to convert to CDI. I had my 125 converted and never looked back. I runs so good I sent my FT-160 in for conversion.
Hobbsy, how does your 150 run at 35 deg BTC?
...
Forum: Glow Engines
01-15-2014, 04:01 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

BLW, how much time on your 125 until you were...

BLW, how much time on your 125 until you were happy with it?

John
Forum: Glow Engines
01-12-2014, 03:01 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

nice!!!!!!

nice!!!!!!
Forum: Glow Engines
12-13-2013, 08:00 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Sending a PM on RCU doesn't seem to be working...

Sending a PM on RCU doesn't seem to be working again.... Go figure. sent PM to SrTelemaster150 (http://www.rcuniverse.com/forum/members/srtelemaster150.html) and blw...
Forum: Glow Engines
12-13-2013, 05:31 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Just received my CDI for the 125..... Wish me...

Just received my CDI for the 125..... Wish me luck!

John
Forum: Glow Engines
12-08-2013, 07:52 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Thanks Sir. I ordered the conversion kit from CH...

Thanks Sir. I ordered the conversion kit from CH today. Any words on Nitro content? Or how far I should lean the carb?

John
Forum: Glow Engines
12-08-2013, 06:49 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

I'll take a number sir!!!!! John

I'll take a number sir!!!!!

John
Forum: Glow Engines
12-07-2013, 04:24 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

Okay.... This thread is so big and I'm going...

Okay.... This thread is so big and I'm going blind trying find specific information within it. I'm sure all this has been answered before, but I hope some of you can send me to the correct pages or...
Forum: Glow Engines
02-21-2011, 04:44 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

I hope it's just a case of me not being a great tuner. If I'm told the crank is the problem, I will probably spend the cash and get a crank and another set of bearings.

I will wait for Mr....
Forum: Glow Engines
02-21-2011, 08:23 AM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

I hope you're right. That's why I'm asking for experienced help.

John
Forum: Glow Engines
02-20-2011, 07:50 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

The setup I have is very similar to yours, but not as refined. I will try and run the 125 again tomorrow with the leaned HS.
Forum: Glow Engines
02-20-2011, 06:06 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

Sorry to be the voice of inexperience here, but that thought did cross my mind and I changed nothing.
The largest engine I have run on my current stand is a ST .75 2 stroke.
Would you suggest...
Forum: Glow Engines
02-20-2011, 05:13 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

Thanks. I will set it a 1 3/4 and run it up again tomorrow. Just looking for some experienced answers.
Forum: Glow Engines
02-20-2011, 04:55 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

The last high end Tach reading I took was a little over 8800 RPM with a 15-8 APC. (the only prop I had left) The HS is only turned out a little more than two turns from bottom. Does this sound...
Forum: Glow Engines
02-20-2011, 02:47 PM
Replies: 54,816
Views: 5,391,457
Posted By johnboy151a

RE: Welcome to Club SAITO !

Sorry to bring up and old topic, especially one that has been beat to death in this forum.

Saito 125 vibration. Same old story. I picked up a 125 on ebay, changed the bearings and cleaned...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.